tag:blogger.com,1999:blog-5466408059280532516.post8488217728832607867..comments2023-04-10T13:47:39.354+01:00Comments on Robotics - Vision Experiments: Re-programming the ROB-09571 (Serial Controlled Motor Driver)Anonymoushttp://www.blogger.com/profile/04206514663069375579noreply@blogger.comBlogger8125tag:blogger.com,1999:blog-5466408059280532516.post-62619501021400420312012-05-14T16:30:48.965+01:002012-05-14T16:30:48.965+01:00According to this post http://arduino.cc/en/Tutori...According to this post http://arduino.cc/en/Tutorial/ArduinoISP it's looking like you need an up to date Uno bootloader and a 10 uF cap on the reset line.Anonymoushttps://www.blogger.com/profile/04206514663069375579noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-10001436462357500942012-05-12T12:14:36.818+01:002012-05-12T12:14:36.818+01:00Hi there,
Glad you got it working :) I don't ...Hi there,<br /><br />Glad you got it working :) I don't have the information for the Uno. I'll have a dig around. It's likely to be either the use of outdated WinAVR, and/or a need for an Uno version of the ArduinoISP sketch.Anonymoushttps://www.blogger.com/profile/04206514663069375579noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-29749938036626023652012-05-08T20:30:03.702+01:002012-05-08T20:30:03.702+01:00Hello,
Thank you so much for this information. D...Hello,<br /><br />Thank you so much for this information. Do you have this information for the Arduino Uno? I almost gave up trying to get this work, when I realized you had this set up for the Duemilanove and was able to re-program the chip successfully once I used a Duemilanove and not an Uno.Unknownhttps://www.blogger.com/profile/07636942434047656390noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-69078663164225568312012-03-16T15:37:03.367+00:002012-03-16T15:37:03.367+00:00No, following through the schematic shows that the...No, following through the schematic shows that the ICSP 2x3 header routes to the SPI port. That cable could hook into the RX/TX/Gnd (with external power source) and may then work with avrdude.Anonymoushttps://www.blogger.com/profile/04206514663069375579noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-83592225149603380702012-03-15T17:04:03.995+00:002012-03-15T17:04:03.995+00:00I have this FTDI cable, 5 volt from sparkfun,
http...I have this FTDI cable, 5 volt from sparkfun,<br />http://www.sparkfun.com/products/9718<br />can I use jumpers to connect it to the 2x3 header on the serial controlled motor board? <br />Thanks.SouthernAtHearthttps://www.blogger.com/profile/17582035372370617116noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-37074876736925497932012-03-12T14:11:37.370+00:002012-03-12T14:11:37.370+00:00Yes. It should be possible to burn the Arduino boo...Yes. It should be possible to burn the Arduino bootloader into the AtMega328.Anonymoushttps://www.blogger.com/profile/04206514663069375579noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-90203432893029538212012-03-12T02:32:16.000+00:002012-03-12T02:32:16.000+00:00Can you write your own arduino code and upload to ...Can you write your own arduino code and upload to this board?SouthernAtHearthttps://www.blogger.com/profile/17582035372370617116noreply@blogger.comtag:blogger.com,1999:blog-5466408059280532516.post-89264482181311865602011-03-03T23:03:09.248+00:002011-03-03T23:03:09.248+00:00EGGS ACTLY WHAT I NEEDED!
Very helpful, clear and ...<b>EGGS ACTLY WHAT I NEEDED!</b><br />Very helpful, clear and well illustrated...<br /><br />Thank you,<br /><br />Paul {Affordable Technology}Anonymousnoreply@blogger.com